Fu-chain conveyor FU series chain conveyor / auger for horizontal conveying powder is a new product of small granular material transport, the auger is technically in the domestic advanced level. The auger reasonable product design, novel structure, energy efficient, seal, secure, and easy maintenance. Origin: China> Hebei> Cangzhou> Botou Supplier: Botou Weill Environmental Protection Equipment Co., Ltd. \ FU-chain conveyor performance FU chain conveyor series (referred to as "chain transporting machine") one with to the horizontal (or inclined 15) conveying powder, granular materials new product small, technically in the domestic advanced level. This product is designed, novel structure, long life, high operational reliability, energy efficient, seal, secure, and easy maintenance. Its performance was significantly better than the screw conveyor, buried scraper conveyor, and other transportation equipment, is an ideal new equipment. Since the products developed by domestic and foreign users, has been widely used in building materials, construction, chemical, thermal power, food processing, mining, machinery, metallurgy, transportation, port and transportation industries. FU chain conveyor Features 1. throughput, and allows a lot of material transport capacity in a small space, conveying capacity 15 ~ 500m3 / h. 2. The delivery of low energy consumption, by means of internal friction materials, compared with the screw conveyor saving 40% to 60%. 3. seals and security, fully sealed enclosure so that dust can seamlessly drill, safe, reliable operation. 4. Long service life, alloy steel conveyor through advanced heat treatment processing, which is the normal life> 3 years, roller life (depending on the material) 1 to 3 years in the chain. 5. The transport length long, horizontal conveying distance up to 60 meters or more. 6. The process layout flexible and can be elevated, ground, ground pit, climbing (15) installed, you can multi-point access to materials. 7. Use low-cost, energy-saving and durable, low maintenance rate, reduce consumption and improve efficiency. FU chain conveyor technology selection and arrangement of the chain conveyor performance specifications included in Table 1. The table lists the capabilities of the various models of delivery in different chain speed. The same amount can be transported to a different table models selected, if the choice of a larger chain models are low-speed, low wear, but higher investment in equipment, if the choice of the smaller models are chain speed quickly, wear relatively high, but the investment in equipment than the province. It should be noted that, when the actual conveying capacity of less than 65% of the transmission capacity of the machine, since the machine tank through the thin layer of material caused by the idle conveyor will increase the wear of the device. Therefore, the actual amount of the recommendations of the conveyor transport not less than the minimum transmission capacity in Table I, the actual amount is multiplied by 1.2 after delivery, the table should not be higher than the maximum transmission capacity. FU chain conveyor specification performance table model machine slot width (mm) optimum throughput (m3 / h) maximum particle size ideal grains (containing not more than 10%) allows inclination material humidity chain speed (m / min) 11 13.5 14 17 21 22 27 28 FU150 150 6-10 10-16 13-20 <4 8 ≤15 ° ≤5% FU200 200 12-18 18-28 25-38 <5 10 FU270 270 22-33 26-40 33- 50 45-68 54-82 86-130 <7 14 FU350 350 43-64 54-80 66-98 120-180 <9 18 FU410 410 60-90 73-110 90-135 <11 21 FU500 500 80-120 105 -160 140-200 180-240 <13 25 FU600 600 120-160 150-220 200-290 240-360 <15 30 when the conveyor is running upward tilt arrangement (ie the feed end at the bottom, the discharge end at the top) its transport capacity will be reduced. In this case the transmission capacity of the conveyor following table shall be multiplied by the discount factor η: conveyor inclination (°) 0-2.5 2.5-5 5-7.5 7.5-10 10-12.5 12.5-15 discount factor η 1 0.95 0.9 0.8 0.8 0.7 drive FU chain conveyor using XWD planetary cycloid reducer. L the length of the conveyor to 0.5 m as a first gear. Standard intermediate segment length FU150,200,270 type conveyor is 2 meters; the middle section of the non-standard length of 1.5 m, 1 m. FU350 type of standard middle section length is 3 meters; the middle section of the non-standard length of 2.5 m, 2 m, 1.5 m. Process layout can be used when the number of sections in the middle section in combination with standard non-standard middle section into a number of sections needed captain L, and the selection criteria as section combinations.